Polymer80 has long been the industry standard for 80% pistol frames. This bundle pack includes the PF940v2™ full-sized frame with all its upgraded features, the compact PF940Cv1™ to use in your next Glock® 19 or 23 compatible builds, and the PF9SS™ single stack frame for your Glock® 43 compatible build.
The PF940v2™ is compatible with Glock® components for Gen 3 3-pin: 9mm G17, 17L, 34; .40S&W G22, 24, 35; and .357Sig G31. Similarly, the PF940Cv1™ is compatible with Glock® components for Gen 3 3-pin: 9mm G19 or the .40SW G23. Finally, the PF9SS™ is compatible with Glock® components for the G43.
Grab the finishing jigs for your frames here!
Grab build kits to assemble your frames here!
These frames feature an extended beavertail and thumb ledge for better control. A double-undercut trigger guard enhances comfort, allowing for a firmer grip. Lastly, engineers upgraded the 22-degree grip angle to 18 degrees. This new angle provides better recoil control and quicker follow-up! Even with a new grip angle, all three of the PF940v2™, the PF940Cv1™, and the PF9SS™ are still compatible with OEM and aftermarket Glock® magazines.
PF940V2™ 80% Frame Features
- Compatible with components for 3-pin (Gen 3) G17, 17L, 22, 24, 31, 34, and G35.
- Improved ergonomics and finish
- Reinforced, hardened polymer
- Factory-style grip texture
PF940Cv1™ 80% Frame Features
- Compatible with components for 3-pin (Gen 3) G19 and G23.
- Improved ergonomics and finish
- Reinforced, hardened polymer
- Factory-style grip texture
PF9SS™ 80% Frame Features
- Compatible with components for 3-pin (Gen 3) G43.
- Improved ergonomics and finish
- Reinforced, hardened polymer
- Factory-style grip texture
Completing Your Frame
In addition to the jig, fabricating your frame requires some basic tools. This kit does not include the other parts required to assemble your pistol once fabrication is complete.
What's Included
- PF940v2™ 80% Full-sized Frame
- PF940Cv1™ 80% Compact Frame
- PF9SS™ 80% Single-Stack Frame
- 80% jig (x3)
- Bits and instructions
- Blank serialization plate on each frame
- Stainless Steel Locking Block Rail (x3)
- Stainless Steel Rear Rail Module (x3)
- Hardened Pins for LBRS and RRM (x3)
NOTE: An end mill bit was deemed unnecessary by Polymer80 and is not included with this kit.
Not a Firearm (State Laws Vary)
Some states have banned receiver blanks and other gun parts. Please check our Shipping Restrictions before placing an order. We cannot fulfill orders in restricted states for any reason.
DISCLAIMER: “GLOCK” is a federally registered trademark of GLOCK, Inc. and is one of many trademarks owned by GLOCK, Inc. and GLOCK Ges.m.b.H. Neither 80 Percent Lowers, a/k/a 80-lower.com nor this site are affiliated in any manner with, or otherwise endorsed by, GLOCK, Inc. or GLOCK Ges.m.b.H. The use of “GLOCK” on this page is merely to advertise the sale of GLOCK pistols, parts, or components. For additional genuine GLOCK, Inc. and GLOCK Ges.m.b.H products and parts visit www.glock.com.
WARNING: Handling firearms parts and accessories can expose you to lead and other petroleum products known to the State of California to cause cancer and reproductive harm. For more information go to: www.P65Warnings.ca.gov
Shipping of various parts and/or accessories are prohibited to states and locales (ie New Jersey, California, New York, etc…) with restrictions against certain parts and/or accessories or "assault weapons" (i.e. states with high-capacity magazine restrictions, manufacturing of semi-automatic weapons, etc..). It is your responsibility to be aware of your local firearms laws before purchasing from our website or machining a firearm. We try our best to keep our shipping page current, but laws change daily.
80-Lower.com only ships within the United States. Federal legislation dictates we cannot ship our products internationally.
