Lifetime Warranty Lifetime Warranty Made in the USA Made in the USA FREE Shipping on $300+

Free Shipping on all orders $325+!

80% Lowers (2-pack) & Easy Jig Gen 1 with Tooling
$354.95 $284.95 (You save $70.00)
Out of Stock Forged Requires Router 80% Lowers (2-pack) & Easy Jig Gen 1 with Tooling - 80% Lowers
Larger / More Photos
Notify Me When Available

Free Shipping on all orders $325+!


80% Lower Jig Quick Reference

Watch the AR-15 Easy Jig GEN 1 Tutorial (Video - 20:12)

(2) Black 80% Lower Receiver:

  • Color: Anodized Black
  • 100% Mil-Spec
  • Quantity: 2
  • Forged 7075-T6 Aluminum
  • Broached Magwell
  • 100% Made in the USA

80% Lower Jig (Easy Jig Gen 1) with Tooling:

  • Can complete 20+ 80% lowers
  • Cuts completion time in half
  • Each plate is replaceable, individually
  • Built-in drill bit depth guides
  • No drill press required (can use standard hand drill)
  • How-To videos and instruction manual
  • Drill bits included:
    • 1) 3/8 drill bit
    • 1) 19/64 drill bit
    • 1) 5/32 drill bit
    • 1) 3/8 drill stop collar
  • End mill bit included:
    • 1) Solid Carbide 1/4 inch end mill - custom made with super short 0.75 in flutes for optimal performance

Note: If you are planning to complete more than 2 lowers, it is recommended that you purchase an end mill bit for every two lowers, and have one extra end mill bit just in case.


See how the Easy Jig GEN 1 (80% Lower Jig) stands up to the others in the 80% Lower Jig Comparison chart.

How easy is it? Read the Easy Jig GEN 1 instruction manual or watch the Easy Jig GEN 1 how-to video.

No FFL Required Made In The USA Lifetime Warranty

Product Videos

80% Arms AR-15 Easy Jig GEN 1 Tutorial 20:12

80% Lowers (2-pack) & Easy Jig Gen 1 with Tooling

$354.95 $284.95 (You save $70.00)
Secure Checkout

Free Shipping on all orders $325+!

Customer Reviews

Based on 23 reviews
5 Star
4 Star
3 Star
2 Star
1 Star
Write a Review Ask a Question
  • Reviews (23)
  • Questions (0)

Thank you for submitting a review!

Your input is very much appreciated. Share it with your friends so they can enjoy it too!


Great jig

"It is a very easy jig to use. I used a drill press, not hand drill. Would like to see a large number engraved on each component but that's solved with a marking pen. Used a full size router."


Scrub your bit.

"If you have a new router make sure you clean the inside of the collet. Make sure you remove any oil residue. The end mill provided should also be cleaned . I used 800 grit sandpaper and then alcohol. Make sure the collet is tighten down properly. I inserted the bit in the router until it bottomed out and then backed it off just a tad. When you get to your final pass if you have to adjust the bit in the collet be very careful and make sure it's tight. If you're going to go to do this , do it right. The jig is a must have. A drill press makes it a lot easier. Take your time. Don't rush. "


great quality

"Love the jigs, I should have purchased this a long time ago. Overall a great deal. "


Great product

Purchased the 2 lowers and jig kit. Followed the instructions and watched a video (still took 2 hrs for me to complete). I was surprised how easy it was to complete. I purchased a lower build kit from local gun store and will be completing the lower this weekend.


1st time AR builder

"I recently received my order for 2 80% receivers along with the jig and tooling. I especially liked the fact that I can get the receiver, jig and tooling at a savings all together. I haven't started the build yet, but I'm excited about that. I've looked over the instructions and they seem fairly easy. I bought this kit because of the good reviews I've read. I've built several AK type rifles from scratch before, but that was drilling and bending so I'm excited to try milling. "